SCC Documentation: docs/tutorial/adding_channels.rst@f51ca1e515ac (annotated)

docs/tutorial/adding_channels.rst@f51ca1e515ac (annotated)

docs/tutorial/adding_channels.rst

Fri, 11 May 2012 14:14:42 +0200

author: ulalume3 <binietoglou@imaa.cnr.it>
date: Fri, 11 May 2012 14:14:42 +0200
changeset 15: f51ca1e515ac
parent 11: 79fea4145278
child 16: 5ffb18491f41
permissions: -rw-r--r--

Ignore everything in the _build folder.

 Adding a channel
 ===============
 After adding a system, a telescope and a laser to the database, you need to add a new channel.
 To do this, click on the **HOI channels** in the *System settings* panel.
 This will take you to a page with a list of all availabe channels that are connected with your lidar systems.
 This list should be empty if this is the first time you add a system.
 To add a new channel to the database click on **Add HOI channel** at the top right of the screen.
 This will take you to a new page were you can fill in the needed information. As before, the fields in **bold**
 are mandatory and you will need to fill them before you can save you new system.
 The fileds you have to fill here are more, as many of these are used during the processing of measurements.
 .. warning::
    There is a last step, different from the previous cases, when saving a new channel. You need to connect your  channel with
    a lidar system before you save, or else all your entry will be lost. Read carefully through this document (or directly
    the :ref:`last section <connect-channel-to-system>`) to avoid any problems.
 Fill in the fields
 ------------------
 To start using the single calculus chain you will need to fill the following fields:
 Name
    The name of the channel ex. "355", "1064 analog" etc.
 Telescope
    The telescope that is used for this channel
 Laser
    The laser that is used for this channel
 Interference filter center
    The center of the interference filter in nm
 Interference filter FWHM
    The FWHM of the interference filter in nm
 Emission wavelength
    The emission wavelength of the laser used for this channel
 Field of view
    The field of view realated to this channel in mrad
 Raw range resolution
    The raw range resolution of the measured data in m
 Dead time
    The dead of the detector in ns. You should fill in this in case
    of a photon counting detector.
 Trigger delay
    The trigger delay value for the channel in ns. Fill in 0 if not needed.
 Scattering mechanism
    The scattering mechanism that is involved in this channel. Select the appropriate value from the drop-down list.
 Dead time correction type
    The dead time correction type to be applied. Select *Not defined* if none needs to be defined.
 Background mode
    The way to calculate the singal background. Select *Not defined* if none needs to be defined.
 Signal type
    The type of the singal that is measured, ex. "elT" for total elastic, "vrRN2" for vibrational-rotational
    Raman signal from Nitrogen melecules etc. See :ref:`signal-types` for details.
 Detection mode
    The detection mode of this channel.
 .. _connect-channel-to-system:
 Connecting to a system
 ----------------------
 Before you finish, you need to attach your channel to one of your systems. To do this, go at the bottom of the page and
 select your system from the drop-down list in the **System channels** area.
 When you are done, press the **save** button at the bottom right of the page.
 This will take you back to the list of your channels.
 If everything went OK your new channel you just added should appear in the list.

Mercurial > public > sccdocs / annotate

docs/tutorial/adding_channels.rst@f51ca1e515ac (annotated)

docs/tutorial/adding_channels.rst