ulalume3@11: ulalume3@11: ulalume3@11: ulalume3@11: ulalume3@11: ulalume3@11: ulalume3@11: ulalume3@11: ulalume3@11: Adding a channel — Single Calculus Chain 0.2 documentation ulalume3@11: ulalume3@11: ulalume3@11: ulalume3@11: ulalume3@11: ulalume3@11: ulalume3@11: ulalume3@11: ulalume3@11: ulalume3@11: ulalume3@11: ulalume3@11: ulalume3@11: ulalume3@11: ulalume3@11: ulalume3@11: ulalume3@11: ulalume3@11:
ulalume3@11:
ulalume3@11:
ulalume3@11:
ulalume3@11: ulalume3@11:
ulalume3@11:

Adding a channel

ulalume3@11:

After adding a system, a telescope and a laser to the database, you need to add a new channel. ulalume3@11: To do this, click on the HOI channels in the System settings panel. ulalume3@11: This will take you to a page with a list of all availabe channels that are connected with your lidar systems. ulalume3@11: This list should be empty if this is the first time you add a system.

ulalume3@11:

To add a new channel to the database click on Add HOI channel at the top right of the screen. ulalume3@11: This will take you to a new page were you can fill in the needed information. As before, the fields in bold ulalume3@11: are mandatory and you will need to fill them before you can save you new system.

ulalume3@11:

The fileds you have to fill here are more, as many of these are used during the processing of measurements.

ulalume3@11:
ulalume3@11:

Warning

ulalume3@11:

There is a last step, different from the previous cases, when saving a new channel. You need to connect your channel with ulalume3@11: a lidar system before you save, or else all your entry will be lost. Read carefully through this document (or directly ulalume3@11: the last section) to avoid any problems.

ulalume3@11:
ulalume3@11:
ulalume3@11:

Fill in the fields

ulalume3@11:

To start using the single calculus chain you will need to fill the following fields:

ulalume3@11:
ulalume3@11:
Name
ulalume3@11:
The name of the channel ex. “355”, “1064 analog” etc.
ulalume3@11:
Telescope
ulalume3@11:
The telescope that is used for this channel
ulalume3@11:
Laser
ulalume3@11:
The laser that is used for this channel
ulalume3@11:
Interference filter center
ulalume3@11:
The center of the interference filter in nm
ulalume3@11:
Interference filter FWHM
ulalume3@11:
The FWHM of the interference filter in nm
ulalume3@11:
Emission wavelength
ulalume3@11:
The emission wavelength of the laser used for this channel
ulalume3@11:
Field of view
ulalume3@11:
The field of view realated to this channel in mrad
ulalume3@11:
Raw range resolution
ulalume3@11:
The raw range resolution of the measured data in m
ulalume3@11:
Dead time
ulalume3@11:
The dead of the detector in ns. You should fill in this in case ulalume3@11: of a photon counting detector.
ulalume3@11:
Trigger delay
ulalume3@11:
The trigger delay value for the channel in ns. Fill in 0 if not needed.
ulalume3@11:
Scattering mechanism
ulalume3@11:
The scattering mechanism that is involved in this channel. Select the appropriate value from the drop-down list.
ulalume3@11:
Dead time correction type
ulalume3@11:
The dead time correction type to be applied. Select Not defined if none needs to be defined.
ulalume3@11:
Background mode
ulalume3@11:
The way to calculate the singal background. Select Not defined if none needs to be defined.
ulalume3@11:
Signal type
ulalume3@11:
The type of the singal that is measured, ex. “elT” for total elastic, “vrRN2” for vibrational-rotational ulalume3@11: Raman signal from Nitrogen melecules etc. See Signal types for details.
ulalume3@11:
Detection mode
ulalume3@11:
The detection mode of this channel.
ulalume3@11:
ulalume3@11:
ulalume3@11:
ulalume3@11:

Connecting to a system

ulalume3@11:

Before you finish, you need to attach your channel to one of your systems. To do this, go at the bottom of the page and ulalume3@11: select your system from the drop-down list in the System channels area.

ulalume3@11:

When you are done, press the save button at the bottom right of the page. ulalume3@11: This will take you back to the list of your channels. ulalume3@11: If everything went OK your new channel you just added should appear in the list.

ulalume3@11:
ulalume3@11:
ulalume3@11: ulalume3@11: ulalume3@11:
ulalume3@11:
ulalume3@11:
ulalume3@11:
ulalume3@11:
ulalume3@11:

Table Of Contents

ulalume3@11: ulalume3@11: ulalume3@11:

Previous topic

ulalume3@11:

Adding equipment

ulalume3@11:

Next topic

ulalume3@11:

Adding products

ulalume3@11:

This Page

ulalume3@11: ulalume3@11: ulalume3@11: ulalume3@11:
ulalume3@11:
ulalume3@11:
ulalume3@11:
ulalume3@11: ulalume3@11: ulalume3@11: ulalume3@11: